Skip to main content

Research Repository

Advanced Search

An experimental investigation of the impact response and post-impact shear buckling behaviour of hybrid composite laminates (2023)
Journal Article
Damghani, M., Saddler, J., Sammon, E., Atkinson, G. A., Matthews, J., & Murphy, A. (2023). An experimental investigation of the impact response and post-impact shear buckling behaviour of hybrid composite laminates. Composite Structures, 305, 116506. https://doi.org/10.1016/j.compstruct.2022.116506

This paper investigates the effect of transverse impact loading on the in-plane shear behaviour of two laminate configurations. The extensive experimental studies consider a pure carbon laminate (type 1) and a novel X-shaped carbon/glass laminate (ty... Read More about An experimental investigation of the impact response and post-impact shear buckling behaviour of hybrid composite laminates.

Investigation of flow augmentation and dynamic stall control devices as performance enhancement of lift-driven vertical axis wind turbine using high-fidelity CFD methods (2022)
Thesis
Syawitri, T. P. Investigation of flow augmentation and dynamic stall control devices as performance enhancement of lift-driven vertical axis wind turbine using high-fidelity CFD methods. (Thesis). University of the West of England. Retrieved from https://uwe-repository.worktribe.com/output/8045334

This study performs an investigation of dynamic stall control (Gurney flap (GF)) and flow augmentation (straight upstream deflector (SUD)) devices to improve the performance of lift-driven Vertical Axis Wind Turbine (VAWT) as they can improve the pow... Read More about Investigation of flow augmentation and dynamic stall control devices as performance enhancement of lift-driven vertical axis wind turbine using high-fidelity CFD methods.

Recycling face masks for manufacturing FlaxPP eco-composites (2022)
Presentation / Conference
ElHawary, O., & Bakthavatchaalam, V. (2022, May). Recycling face masks for manufacturing FlaxPP eco-composites. Poster presented at United Nations University: Nexus Conference, Dresden/Online

SDGs addressed: 9, 11, 12, 14 and 15. Introduction: The severe increase in the pollution caused by the discarded face masks during COVID-19 cannot be overstated. This research provides an innovative engineering solution to this issue by recycling p... Read More about Recycling face masks for manufacturing FlaxPP eco-composites.

Aerodynamic and aeroacoustic analysis of a harmonically morphing airfoil using dynamic meshing (2021)
Journal Article
Abdessemed, C., Bouferrouk, A., & Yao, Y. (2021). Aerodynamic and aeroacoustic analysis of a harmonically morphing airfoil using dynamic meshing. Acoustics, 3(1), 177-199. https://doi.org/10.3390/acoustics3010013

This work explores the aerodynamic and aeroacoustic responses of an airfoil fitted with a harmonically morphing Trailing Edge Flap (TEF). An unsteady parametrization method adapted for harmonic morphing is introduced, and then coupled with dynamic me... Read More about Aerodynamic and aeroacoustic analysis of a harmonically morphing airfoil using dynamic meshing.

Using laminate hybridisation (CFRP-GFRP) and shaped CFRP plies to increase plate post-buckling strain to failure under shear loading (2021)
Journal Article
Damghani, M., Wallis, C., Bakunowicz, J., & Murphy, A. (2021). Using laminate hybridisation (CFRP-GFRP) and shaped CFRP plies to increase plate post-buckling strain to failure under shear loading. Thin-Walled Structures, 162, Article 107543. https://doi.org/10.1016/j.tws.2021.107543

Previous works have established the response and failure behaviour of hybrid (CFRP-GFRP) laminates when subjected to a wide range of destabilising loads. However, to date no works have quantified the influence of selective laminate shapes and hybridi... Read More about Using laminate hybridisation (CFRP-GFRP) and shaped CFRP plies to increase plate post-buckling strain to failure under shear loading.

Detection of aircraft touchdown using longitudinal acceleration and continuous wavelet transformation (2020)
Journal Article
Bakunowicz, J., & Rzucidło, P. (2020). Detection of aircraft touchdown using longitudinal acceleration and continuous wavelet transformation. Sensors, 20(24), 1-25. https://doi.org/10.3390/s20247231

The paper presents a methodology enabling the detection of aircraft touchdowns based on data obtained from accelerometers attached to the structural parts of the airframe in the cockpit or passenger compartment. Precise determination of the moment an... Read More about Detection of aircraft touchdown using longitudinal acceleration and continuous wavelet transformation.

Experimental evaluation of residual tensile strength of hybrid composite aerospace materials after low velocity impact (2019)
Journal Article
Damghani, M., Ersoy, N., Piorkowski, M., & Murphy, A. (2019). Experimental evaluation of residual tensile strength of hybrid composite aerospace materials after low velocity impact. Composites Part B: Engineering, 179, Article 107537. https://doi.org/10.1016/j.compositesb.2019.107537

© 2019 Elsevier Ltd Although much work has considered hybridised Carbon and Glass Fibre Reinforced Polymers to positively influence the performance of composite structures when subjected to transverse impact loading, there is limited understanding co... Read More about Experimental evaluation of residual tensile strength of hybrid composite aerospace materials after low velocity impact.

Dynamic mesh framework for morphing wings CFD (2019)
Thesis
Abdessemed, C. Dynamic mesh framework for morphing wings CFD. (Thesis). University of the West of England. Retrieved from https://uwe-repository.worktribe.com/output/1490739

In this work, a framework to perform high fidelity Computational Fluid Dynamics (CFD) analysis of dynamically morphing airfoils and wings is presented. An unsteady parametric method to model the deforming motion is proposed and then implemented in a... Read More about Dynamic mesh framework for morphing wings CFD.

Marimo machines: Oscillators, biosensors and actuators (2019)
Journal Article
Phillips, N., Draper, T. C., Mayne, R., & Adamatzky, A. (2019). Marimo machines: Oscillators, biosensors and actuators. Journal of Biological Engineering, 13(1), Article 72. https://doi.org/10.1186/s13036-019-0200-5

Background The green algae balls (Aegagropila linnaei), known as Marimo, are large spherical colonies of live photosynthetic filaments, formed by rolling water currents in freshwater lakes. Photosynthesis therein produces gas bubbles that can attach... Read More about Marimo machines: Oscillators, biosensors and actuators.

Dr Alex Moulton CBE RDI 1920-2012 (2015)
Presentation / Conference
Barker, P., Frayling, C., Conran, S., Farrell, D., Hadland, T., & Stone, D. (2015, April). Dr Alex Moulton CBE RDI 1920-2012. Presented at Dr Alex Moulton CBE RDI 1920-2012, Central Saint Martins, London UK

Chaired by Professor Sir Christopher Frayling this half day seminar included presentations from Sebastian Conran, Tony Hadland, Dominic Stone, Dan Farrell and Peter Barker on the bicycle, automotive and other works of this seminal figure of 20th ce... Read More about Dr Alex Moulton CBE RDI 1920-2012.

Time-dependent thermo-creep analysis of rotating FGM thick-walled cylindrical pressure vessels under heat flux (2014)
Journal Article
Nejad, M. Z., & Davoudi Kashkoli, M. (2014). Time-dependent thermo-creep analysis of rotating FGM thick-walled cylindrical pressure vessels under heat flux. International Journal of Engineering Science, 82, 222-237. https://doi.org/10.1016/j.ijengsci.2014.06.006

In the present study, time-dependent thermoelastic creep response for isotropic rotating thick-walled cylindrical pressure vessels made of functionally graded material (FGM) has been investigated, taking into account the creep behavior of the FGM pre... Read More about Time-dependent thermo-creep analysis of rotating FGM thick-walled cylindrical pressure vessels under heat flux.