Richard J. Preen
3D printed components of microbial fuel cells: Towards monolithic microbial fuel cell fabrication using additive layer manufacturing
Preen, Richard J.; You, Jiseon; Preen, Richard; Bull, Larry; Greenman, John; Ieropoulos, Ioannis
Authors
Jiseon You Jiseon.You@uwe.ac.uk
Lecturer in Engineering/ Project Management
Richard Preen Richard2.Preen@uwe.ac.uk
Research Fellow in Machine Learning
Lawrence Bull Larry.Bull@uwe.ac.uk
AHOD Research and Scholarship and Prof
John Greenman
Yannis Ieropoulos Ioannis2.Ieropoulos@uwe.ac.uk
Professor in Bioenergy & Director of B-B
Abstract
© 2016 The Authors For practical applications of the MFC technology, the design as well as the processes of manufacturing and assembly, should be optimised for the specific target use. Another burgeoning technology, additive manufacturing (3D printing), can contribute significantly to this approach by offering a high degree of design freedom. In this study, we investigated the use of commercially available 3D printable polymer materials as the MFC membrane and anode. The best performing membrane material, Gel-Lay, produced a maximum power of 240 ± 11 μW, which was 1.4-fold higher than the control CEM with PMAX of 177 ± 29 μW. Peak power values of Gel-Lay (133.8–184.6 μW) during fed-batch cycles were also higher than the control (133.4–160.5 μW). In terms of material cost, the tested membranes were slightly higher than the control CEM, primarily due to the small purchased quantity. Finally, the first 3D printable polymer anode, a conductive PLA material, showed significant potential as a low-cost and easy to fabricate MFC anode, producing a stable level of power output, despite poor conductivity and relatively small surface area per unit volume. These results demonstrate the practicality of monolithic MFC fabrication with individually optimised components at relatively low cost.
Citation
Preen, R. J., You, J., Preen, R., Bull, L., Greenman, J., & Ieropoulos, I. (2017). 3D printed components of microbial fuel cells: Towards monolithic microbial fuel cell fabrication using additive layer manufacturing. Sustainable Energy Technologies and Assessments, 19, 94-101. https://doi.org/10.1016/j.seta.2016.11.006
Journal Article Type | Article |
---|---|
Acceptance Date | Nov 29, 2016 |
Online Publication Date | Dec 29, 2016 |
Publication Date | Feb 1, 2017 |
Journal | Sustainable Energy Technologies and Assessments |
Print ISSN | 2213-1388 |
Publisher | Elsevier |
Peer Reviewed | Peer Reviewed |
Volume | 19 |
Pages | 94-101 |
DOI | https://doi.org/10.1016/j.seta.2016.11.006 |
Keywords | microbial fuel cell (MFC), 3D printing, additive manufacturing (AM), polymer membrane, PLA based polymer anode |
Public URL | https://uwe-repository.worktribe.com/output/899226 |
Publisher URL | http://dx.doi.org/10.1016/j.seta.2016.11.006 |
Additional Information | Additional Information : The dataset for this study is available from the UWE Research Data Repository: http://researchdata.uwe.ac.uk/180/ |
Files
1-s2.0-S2213138816302090-main.pdf
(1.7 Mb)
PDF
You might also like
Small ceramic microbial fuel cell as a trigenerative system for electricity, organics degradation and urine filtration
(2018)
Presentation / Conference
Anode surface modification with activated carbon for improved power generation in urine fed Microbial Fuel Cells
(2018)
Presentation / Conference
Development of small scale ceramic Microbial Fuel Cells for clean energy extraction from urine
(2018)
Presentation / Conference
3D-printable cathode electrode for monolithically printed microbial fuel cells (MFCs)
(2018)
Presentation / Conference
Small scale ceramic MFCs for efficient energy harvesting from wastewater and full system development
(2016)
Presentation / Conference