Dr Jun Yao's Outputs (79)

Investigation of microjet engine inlet pressure distortions at angled inflow velocity conditions (2025)
Journal Article

The Armfield CM14 microjet axial flow turbine engine has been tested in open space at ambient conditions with engine inlet pressure at the aerodynamic interface plane (AIP) measured by a built-in pressure sensor for validating computational fluid dyn... Read More about Investigation of microjet engine inlet pressure distortions at angled inflow velocity conditions.

Drag reduction of lift-type vertical axis wind turbine with slit modified gurney flap (2024)
Journal Article

This study examines aerodynamic performance enhancement of Vertical Axis Wind Turbine (VAWT) blades with Gurney flap (GF) modified by slits. A quasi-3D computational fluid dynamics solution based on Reynolds-averaged Navier-Stokes model is employed t... Read More about Drag reduction of lift-type vertical axis wind turbine with slit modified gurney flap.

Numerical simulation and experimental investigation of the effect of three-layer annular coaxial shroud on gas-powder flow in laser cladding (2022)
Journal Article

Laser cladding is a notable metal additive manufacturing (AM). The outstanding benefit of laser cladding is that the cladding process is more flexible and it can be completed in an open environment. However, oxidation phenomenon of active metals such... Read More about Numerical simulation and experimental investigation of the effect of three-layer annular coaxial shroud on gas-powder flow in laser cladding.

Unsteady flow oscillations in a 3-D ventilated model room with convective heat transfer (2022)
Journal Article

Improving indoor air quality and energy consumption is one of the high demands in the building sector. In this study, unsteady flow oscillations in a 3-D ventilated model room with convective heat transfer have been studied for three configurations o... Read More about Unsteady flow oscillations in a 3-D ventilated model room with convective heat transfer.

Transient CFD modelling of air–water two-phase annular flow characteristics in a small horizontal circular pipe (2022)
Journal Article

The liquid film formed around the inner walls of a small horizontal circular pipe often exhibits non-uniform distributions circumferentially, where the film is thinner at the top surface than the bottom one. Even with this known phenomenon, the probl... Read More about Transient CFD modelling of air–water two-phase annular flow characteristics in a small horizontal circular pipe.

Optimisation of straight plate upstream deflector for the performance enhancement of vertical axis wind turbine at low, medium and high regimes of tip speed ratios (2022)
Journal Article

Location and geometry optimisations of Straight Plate Upstream Deflector (SPUD) for performance enhancement of a three-straightbladed Vertical Axis Wind Turbine (VAWT) are carried out at three regimes of tip speed ratios (TSRs). Results analysis reve... Read More about Optimisation of straight plate upstream deflector for the performance enhancement of vertical axis wind turbine at low, medium and high regimes of tip speed ratios.

A review on the use of passive flow control devices as performance enhancement of lift-type vertical axis wind turbines (2022)
Journal Article

This article provides a comprehensive review about passive flow control devices (PFCDs) implemented in lift-type vertical axis wind turbine (LVAWT), focusing on the underlying flow physics mechanisms and to what extents they can improve the LVAWT per... Read More about A review on the use of passive flow control devices as performance enhancement of lift-type vertical axis wind turbines.

Geometry optimisation of vertical axis wind turbine with Gurney flap for performance enhancement at low, medium and high ranges of tip speed ratios (2021)
Journal Article

Optimisation of Gurney flap (GF) geometries mounted on a three-straight-bladed vertical axis wind turbine (VAWT) is evaluated with computational fluid dynamics (CFD) solution and Taguchi method, considering the blade rotating effect at three tip spee... Read More about Geometry optimisation of vertical axis wind turbine with Gurney flap for performance enhancement at low, medium and high ranges of tip speed ratios.

Comparison study of URANS and hybrid RANS-LES models on predicting vertical axis wind turbine performance at low, medium and high tip speed ratio ranges (2020)
Journal Article

Comparison study of unsteady Reynolds-averaged Navier-Stokes (URANS) and hybrid RANS-LES models is carried out for predicting the performance of three-straight-bladed vertical axis wind turbine operating within tip speed ratios (TSRs) ranges of (1.44... Read More about Comparison study of URANS and hybrid RANS-LES models on predicting vertical axis wind turbine performance at low, medium and high tip speed ratio ranges.

Flow analysis in right-angled pipes with different geometric shapes and parameters for sludge discharge in slime shield machines measured using a CFD-DEM method (2020)
Journal Article

Mud and gravel deposition often occurs in circulation systems of pumps. In this paper, a liquid-solid coupling method combining CFD and DEM is proposed to study two-phase flow behavior of water, The flow characteristics of water-clay mud and the moti... Read More about Flow analysis in right-angled pipes with different geometric shapes and parameters for sludge discharge in slime shield machines measured using a CFD-DEM method.

Assessment of stress-blended eddy simulation model for accurate performance prediction of vertical axis wind turbine (2020)
Journal Article

Purpose: The aim of this paper is to assess the ability of a stress-blended eddy simulation (SBES) turbulence model to predict the performance of a three-straight-bladed vertical axis wind turbine (VAWT). The grid sensitivity study is conducted to ev... Read More about Assessment of stress-blended eddy simulation model for accurate performance prediction of vertical axis wind turbine.

The effect of gurney flap on flow characteristics of vertical axis wind turbine (2020)
Journal Article

Recently, the Gurney Flap (GF) has been used to improve the performance of Horizontal Axis Wind Turbine (HAWT) by enhancing its lift coefficient. Compared to HAWT, research on GF application for Vertical Axis Wind Turbine (VAWT) is very limited. More... Read More about The effect of gurney flap on flow characteristics of vertical axis wind turbine.

Surface flow modification of aerofoils for automotive racing car applications (2020)
Journal Article

An aerofoil commonly used in aerospace engineering to produce lift is also employed in the motor sport industry to produce downforce for improving traction during cornering. This paper investigates aerofoil surface modification through 'golf ball dim... Read More about Surface flow modification of aerofoils for automotive racing car applications.

Detached eddy simulation of blade trailing-edge cutback cooling performance at various ejection slot angles (2019)
Journal Article

© 2019 Elsevier Inc. Detached eddy simulation (DES) has been carried out to study a three-dimensional trailing-edge (TE) cutback turbine blade model with five rows of staggered circular pin-fin arrays inside the cooling passage, in order to evaluate... Read More about Detached eddy simulation of blade trailing-edge cutback cooling performance at various ejection slot angles.

Pin-fin shape and orientation effects on wall heat transfer predictions of gas turbine blade (2019)
Presentation / Conference Contribution

Turbine blades are often exposed to the ‘hot’ gas environment and thus it is essential to apply effective cooling technique to extend the blade lifetime. In the present work, wall heat transfer characteristics inside a blade trailing-edge coolant pas... Read More about Pin-fin shape and orientation effects on wall heat transfer predictions of gas turbine blade.

Surface flow modification of aerofoils for automative racing car application (2019)
Presentation / Conference Contribution

An aerofoil which is commonly used in aerospace engineering to produce lift is also employed in the motorsport industry to produce downforce for improving traction in cornering. This paper investigates aerofoil surface modification through ‘golf ball... Read More about Surface flow modification of aerofoils for automative racing car application.

Assessment of stress-blended eddy simulation model for accurate prediction of three-straight-bladed vertical axis wind turbine performance (2019)
Presentation / Conference Contribution

The performance of a three-straight-bladed vertical axis wind turbine at low tip speed ratio has been evaluated by detached eddy simulation (DES) with stress-blended eddy simulation (SBES) turbulence model. Two grid topologies around the blades, i.e.... Read More about Assessment of stress-blended eddy simulation model for accurate prediction of three-straight-bladed vertical axis wind turbine performance.

CFD simulation of three-straight-bladed vertical axis wind turbine at low tip speed ratios (2018)
Presentation / Conference Contribution

This paper presents computational fluid dynamics (CFD) simulations of a three-straight-bladed Vertical Axis Wind Turbine (VAWT) operating at a wind speed of 9 m/s and low Tip Speed Ratio (TSR) ranging from 1.44 to 3.3. The turbine blade has NACA 0021... Read More about CFD simulation of three-straight-bladed vertical axis wind turbine at low tip speed ratios.

Zeolite supported platinum nanoparticles for small organic molecule oxidation and reduction in fuel cell using impregnation (2018)
Presentation / Conference Contribution

Zeolite supported Pd electrocatalyst nanoparticle characterization (2018)
Journal Article

© 2018 Hydrogen Energy Publications LLC A laboratory made 1.5 wt% Palladium (Pd) zeolite electrocatalyst is investigated using the Extended X-ray Adsorption Fine Structure (EXAFS) and Cyclic Voltammetry (CV) techniques to reveal Pd structure and resu... Read More about Zeolite supported Pd electrocatalyst nanoparticle characterization.