All Outputs (12)

Dock-to-dock multimodal freight transportation in coastal regions (2022)
Presentation / Conference Contribution

The Dock to Dock (D2D) project defines the primary infrastructure for future electric freight transport solutions between coastal cities, in particular the energy infrastructure (battery charging/hydrogen refuelling) required for ground vehicles, and... Read More about Dock-to-dock multimodal freight transportation in coastal regions.

Targeting global environmental challenges by the means of novel multimodal transport: Concept of operations (2021)
Presentation / Conference Contribution

Novel modes of transport form the basis of environmentally friendly and economically efficient transport system of the future. This paper introduces the feasibility study of a Dock to Dock (D2D) use case, combining aspects of route development and in... Read More about Targeting global environmental challenges by the means of novel multimodal transport: Concept of operations.

Using laminate hybridisation (CFRP-GFRP) and shaped CFRP plies to increase plate post-buckling strain to failure under shear loading (2021)
Journal Article

Previous works have established the response and failure behaviour of hybrid (CFRP-GFRP) laminates when subjected to a wide range of destabilising loads. However, to date no works have quantified the influence of selective laminate shapes and hybridi... Read More about Using laminate hybridisation (CFRP-GFRP) and shaped CFRP plies to increase plate post-buckling strain to failure under shear loading.

Detection of aircraft touchdown using longitudinal acceleration and continuous wavelet transformation (2020)
Journal Article

The paper presents a methodology enabling the detection of aircraft touchdowns based on data obtained from accelerometers attached to the structural parts of the airframe in the cockpit or passenger compartment. Precise determination of the moment an... Read More about Detection of aircraft touchdown using longitudinal acceleration and continuous wavelet transformation.

Understanding the influence of laminate stacking sequence on strain/stress concentrations in thin laminates at repair holes with large scarf angles (2019)
Journal Article

Scarf repair is widely used in the restoration of structural performance of damaged aircraft secondary structures. Such repairs result in reduced thickness sections which are significantly larger than those associated with typical fastener holes. Sig... Read More about Understanding the influence of laminate stacking sequence on strain/stress concentrations in thin laminates at repair holes with large scarf angles.

Small aircraft infrared radiation measurements supporting the engine airframe aero-thermal integration (2019)
Journal Article

© 2018 Budapest University of Technology and Economics. All rights reserved. The large, EU Supported ESPOSA (Efficient Systems and propulsion for Small Aircraft) project has developed new small gas turbines for small aircraft. One of the important ta... Read More about Small aircraft infrared radiation measurements supporting the engine airframe aero-thermal integration.

Single engine turboprop aeroplane class in small air transport (2018)
Journal Article

Purpose: This paper aims to present the analysis of introduction of single engine turbo-prop aeroplane class in terms of certification specifications and flight crew licensing regulations. Design/methodology/approach: Following the results of flight... Read More about Single engine turboprop aeroplane class in small air transport.

Buckling deformation of thin layer coverings of small curvatures used in aircraft construction (2018)
Journal Article

This paper presents the results of the experimental and numerical analysis in terms of the finite element method of plating components of aircraft load-bearing structures. The subject matter of the study was composite panels with stiffeners in the fo... Read More about Buckling deformation of thin layer coverings of small curvatures used in aircraft construction.

Measurement and analysis of certain flight parameters based on MEMS sensors (2017)
Journal Article

© 2017 Author(s). Gyroscopes established one of the fundamental references for attitude and heading in aerospace applications. The information about angular velocities gives input not only for autopilot, but also damping devices, such as yaw or pitch... Read More about Measurement and analysis of certain flight parameters based on MEMS sensors.

Measuring structure deformations of a composite glider by optical means with on-ground and in-flight testing (2016)
Journal Article

© 2016 IOP Publishing Ltd. In aeronautical research experimental data sets of high quality are essential to verify and improve simulation algorithms. For this reason the experimental techniques need to be constantly refined. The shape, movement or de... Read More about Measuring structure deformations of a composite glider by optical means with on-ground and in-flight testing.

In-flight wing deformation measurements on a glider (2016)
Journal Article

© 2016 Royal Aeronautical Society. Flight testing is both vital for collecting data for aeronautic research and at the same time fascinating for its contributors. Taking a glider as a versatile test bed example, this paper presents a transnational me... Read More about In-flight wing deformation measurements on a glider.

Effect of stiffeners on nature of post-critical deformations of thin-walled composite aircraft structures: A combined numerical-experimental study (2016)
Presentation / Conference Contribution

© 2016 IEEE. This paper presents results of numerical and experimental examination of thin-walled structures which model certain parts of aircraft structures subject to bending and torsion. The considered type of load and deformation corresponds to t... Read More about Effect of stiffeners on nature of post-critical deformations of thin-walled composite aircraft structures: A combined numerical-experimental study.