Skip to main content

Research Repository

Advanced Search

Dr Shwe Soe's Outputs (53)

Novel use of robotic 3D paste printing technology for the creation of ceramic shell investment casting moulds (2023)
Presentation / Conference Contribution

This paper presentation outlines early-stage, ongoing research into novel approaches with Additive Layer Manufacturing for the direct manufacture of ceramic shell investment casting moulds. The research is focused on the use of 3D printing with refra... Read More about Novel use of robotic 3D paste printing technology for the creation of ceramic shell investment casting moulds.

Compressive behaviour of a square origami surface-based lattice structure fabricated by selective laser melting (2023)
Presentation / Conference Contribution

Selective laser melting (SLM) is a metal additive manufacturing process that shows significant advantages in manufacturing lattice structures. In this paper, a novel surface-based square origami structure made of a nickel-based superalloy was fabrica... Read More about Compressive behaviour of a square origami surface-based lattice structure fabricated by selective laser melting.

An explorative study on the antimicrobial effects and mechanical properties of 3D printed PLA and TPU surfaces loaded with Ag and Cu against nosocomial and foodborne pathogens (2022)
Journal Article

Antimicrobial 3D printed surfaces made of PLA and TPU polymers loaded with copper (Cu), and silver (Ag) nanoparticles (NPs) were developed via fused deposition modeling (FDM). The potential antimicrobial effect of the 3D printed surfaces against Esch... Read More about An explorative study on the antimicrobial effects and mechanical properties of 3D printed PLA and TPU surfaces loaded with Ag and Cu against nosocomial and foodborne pathogens.

Laser powder bed fusion of TiB2-modified Cu15Ni8Sn alloy: Processability, microstructure and mechanical performance (2022)
Journal Article

Cu15Ni8Sn is widely used in the aerospace and electronics domains because of its good conductivity and toughness. Due to the material's high laser reflectivity and thermal conductivity, however, employing the laser powder bed fusion (LPBF) additive m... Read More about Laser powder bed fusion of TiB2-modified Cu15Ni8Sn alloy: Processability, microstructure and mechanical performance.

Mechanical behaviour of additively manufactured elastomeric pre-buckled honeycombs under quasi-static and impact loading (2022)
Journal Article

Selective laser sintering has been used to manufacture different structural variations of a pre-buckled circular honeycomb. The mechanical behaviour of these structures has been examined under both quasi-static and dynamic impact loading. Pre-buckled... Read More about Mechanical behaviour of additively manufactured elastomeric pre-buckled honeycombs under quasi-static and impact loading.

Investigating the dynamic compression response of elastomeric, additively manufactured fluid-filled structures via experimental and finite element analyses (2021)
Journal Article

This study evaluates a fluid-filled, closed-cell lattice as a novel route to reducing peak acceleration in impact environments. A conical structure was designed and built using fused filament fabrication. One structure was manufactured hollow (100% a... Read More about Investigating the dynamic compression response of elastomeric, additively manufactured fluid-filled structures via experimental and finite element analyses.

Laser powder bed fusion of WC-reinforced Hastelloy-X composite: Microstructure and mechanical properties (2020)
Journal Article

Nickel-based superalloys such as Hastelloy X (HX) are widely used in gas turbine engines for their exceptional oxidation resistance and high-temperature strength. The addition of ceramic reinforcement further enhances these superalloys’ mechanical pe... Read More about Laser powder bed fusion of WC-reinforced Hastelloy-X composite: Microstructure and mechanical properties.

The effect of heat treatment of AlSi10Mg on the energy absorption performance of surface-based structures (2020)
Presentation / Conference Contribution

Additive Manufacturing of cellular lattice structures offers opportunities to fine-tune the mechanical response by altering geometric variables. It is known that heat treatment cycles provide an effective way of altering mechanical properties while r... Read More about The effect of heat treatment of AlSi10Mg on the energy absorption performance of surface-based structures.

Effect of hot cracking on the mechanical properties of Hastelloy X superalloy fabricated by laser powder bed fusion additive manufacturing (2019)
Journal Article

Nickel-based superalloys such as Hastelloy X (HX) are widely used in gas turbine engine applications and the aerospace industry. HX is susceptible to hot cracking, however, when processed using additive manufacturing technologies such as laser powder... Read More about Effect of hot cracking on the mechanical properties of Hastelloy X superalloy fabricated by laser powder bed fusion additive manufacturing.

Mechanical characterisation of additively manufactured elastomeric structures for variable strain rate applications (2019)
Journal Article

© 2019 Elsevier B.V. Additive manufacturing (AM) enables production of geometrically-complex elastomeric structures. The elastic recovery and strain-rate dependence of these materials means they are ideal for use in dynamic, repetitive mechanical loa... Read More about Mechanical characterisation of additively manufactured elastomeric structures for variable strain rate applications.