Graham Johnson
Windage power losses from spiral bevel gears with varying oil flows and shroud configurations
Johnson, Graham; Chandra, Budi; Foord, Colin; Simmons, Kathy
Authors
Budi Chandra Budi.Chandra@uwe.ac.uk
Associate Director (Mobility Technologies)
Colin Foord
Kathy Simmons
Abstract
In many aero-engines, the power to drive accessories is transmitted through high speed bevel gears in a chamber in the center of the engine. The windage power loss (WPL) associated with these gears makes a significant contribution to the overall heat generation within the chamber. Shrouding the gears provides an effective method of reducing this WPL and managing the flow of lubricating oil. Experimental and computational programs at the University of Nottingham Technology Centre in Gas Turbine Transmission Systems are providing an improved understanding of shroud performance and design. This paper presents the results from a pair of shrouded meshing gears run at representative speeds and oil flow in a rig with speed and torque measurement. A previously published study of a single bevel gear operating in air (Johnson et al., 2007, "Experimental Investigation Into Windage Power Loss From a Shrouded Spiral Bevel Gear" ASME Paper No. GT2007-27885) found a reduction in torque of up to 70% from shrouding. In this work, the addition of oil and the pinion gear did not lead to high torque due to the buildup of oil under the shrouds, but the reduction in torque due to fitting the shrouds is significantly less than was found for the same gear in air alone. In order to isolate the various parameters, further testing with a single gear was carried out. A fully (360 deg) shrouded gear shows a big improvement over an unshrouded gear when running in air alone, but much of this benefit disappears as soon as a very small amount of oil is introduced under the shroud. This implies that the oil is recirculating under the shroud. Increasing the oil flow beyond this initial level increases the torque by the amount required to accelerate the oil mass flow up to the peripheral speed of the gear. Providing a full width slot in the shroud downstream of the oil jet allows the oil to escape without any recirculation and restores much of the benefit of the shroud. Further insight into the oil behavior is obtained from torque measurements and observations through a transparent shroud and with various slot configurations. Video observation shows evidence of a vortex flow under the shroud that carries some of the oil toward the inner diameter of the gear. The three main windage contributors, air alone, recirculation of oil under the shroud, and acceleration of the feed oil, are quantified and methods for achieving the optimum design are discussed. © 2009 by ASME.
Journal Article Type | Article |
---|---|
Acceptance Date | Jul 13, 2009 |
Publication Date | Oct 1, 2009 |
Journal | Journal of Turbomachinery |
Print ISSN | 0889-504X |
Electronic ISSN | 1528-8900 |
Publisher | American Society of Mechanical Engineers |
Peer Reviewed | Peer Reviewed |
Volume | 131 |
Issue | 4 |
Pages | 1-7 |
DOI | https://doi.org/10.1115/1.3072519 |
Keywords | gear windage, gas turbine, multiphase flow, internal gear box |
Public URL | https://uwe-repository.worktribe.com/output/994382 |
Publisher URL | http://dx.doi.org/10.1115/1.3072519 |
You might also like
Experimental investigation into the performance of shallow aeroengine off-takes
(2014)
Presentation / Conference Contribution
Transient two-phase effects in an Aeroengine bearing chamber scavenge test rig
(2014)
Presentation / Conference Contribution
CFD simulation of three-straight-bladed vertical axis wind turbine at low tip speed ratios
(2018)
Presentation / Conference Contribution
Assessment of stress-blended eddy simulation model for accurate prediction of three-straight-bladed vertical axis wind turbine performance
(2019)
Presentation / Conference Contribution
A review of current technical development in vertical axis wind turbine technologies and their braking system for low speed, urban and offshore areas application
(2018)
Presentation / Conference Contribution
Downloadable Citations
About UWE Bristol Research Repository
Administrator e-mail: repository@uwe.ac.uk
This application uses the following open-source libraries:
SheetJS Community Edition
Apache License Version 2.0 (http://www.apache.org/licenses/)
PDF.js
Apache License Version 2.0 (http://www.apache.org/licenses/)
Font Awesome
SIL OFL 1.1 (http://scripts.sil.org/OFL)
MIT License (http://opensource.org/licenses/mit-license.html)
CC BY 3.0 ( http://creativecommons.org/licenses/by/3.0/)
Powered by Worktribe © 2024
Advanced Search